We can also call it silicon calcium board. Gypsum composite board is a common thermal insulation material, which is widely used in indoor partition insulation. But do you know what is included in the construction process of gypsum composite board partition insulation?

墻位放線：按照設計圖紙?jiān)跇堑孛?、墻面、頂面和主體結構墻面彈出定位線和邊線，并彈出門窗口線。墻基施工：墻基施工前，樓地面應進行毛化處理，并涂刷固央墻地界面寶，現澆墻基混凝土。

Wall setting out: snap positioning lines and sidelines on the floor, wall, top and main structure wall according to the design drawings, and snap the door and window opening lines. Wall foundation construction: before the construction of wall foundation, the floor shall be roughened, painted with solid central wall ground interface, and cast-in-situ wall foundation concrete.

預排：量準隔墻凈空高度、寬度及門窗口尺寸，在地面上進行預排列。設有門窗的隔墻，應先安裝窗口上、下和門上的短板，再順序安裝門窗口兩側的隔墻板，如剩余墻寬不足整板時，則按實際墻寬補板。

Pre arrangement: measure the clearance height and width of the partition wall and the size of the door and window, and pre arrange it on the ground. For the partition wall with doors and windows, the short plates on the upper, lower and door of the window shall be installed first, and then the partition plates on both sides of the door and window shall be installed in sequence. If the remaining wall width is less than the whole plate, the plate shall be supplemented according to the actual wall width.

安裝：石膏復合板安裝時，在板的頂面、側面和板與板之間，均勻涂抹一層膠黏劑，然后上下頂緊，側面要嚴實，縫內膠黏劑要飽滿。板下所塞木楔，一般不撤除，但不得露出墻外。首塊石膏復合板安裝好后，要檢查其垂直度，繼續安裝時，須上，下橫靠檢查尺，開與板面找平當板面不平時，應及時糾正復合板與兩端主體結構連接要牢固。

Installation: during the installation of gypsum composite board, apply a layer of adhesive evenly on the top and side of the board and between the board and the board, and then press it up and down. The side should be tight and the adhesive in the joint should be full. The wooden wedge under the slab shall not be removed generally, but shall not be exposed outside the wall. After the first gypsum composite board is installed, its perpendicularity shall be checked. When continuing the installation, it must lean against the inspection ruler up and down, open and level with the board surface. When the board surface is uneven, it shall be corrected in time, and the connection between the composite board and the main structure at both ends shall be firm.

以上就是今天帶給大家的知識濟南泡沫復合板專注行業多年，為用戶不斷的提供有價值的內容，更多內容請繼續關注我們：http://m.gp552.com

The above is the knowledge that we bring to you today. Ji'nan foam composite board has been focusing on the industry for many years, providing users with valuable content continuously. http://m.gp552.com