彩鋼瓦的安裝給建筑帶來了使用的保證。該產品使用牢固美觀，但大多數人對其切角過程了解不多。它主要是為了使它的棱角整齊，這樣你在使用它的時候就會發現它更加統一。接下來，讓我們了解一下濟南彩鋼瓦的切角過程，感興趣的朋友可以關注一下。

The installation of color steel tile has brought the guarantee of use to the building. The product is firm and beautiful to use, but most people do not know much about its chamfering process. It is mainly used to make its edges and corners neat, so that when you use it, you will find it more uniform. Next, let's learn about the chamfering process of Jinan color steel tile, and interested friends can pay attention to it.

便攜式夾芯板節省了大量的安裝時間，因為它相對堅固，不影響建筑物的強度。同時，其防火性能為建筑增加了保證。它被整齊地切割在邊緣和角落。在后期施工中，特別是在對齊環節時，它會很輕。

The portable sandwich panel saves a lot of installation time because it is relatively solid and does not affect the strength of the building. At the same time, its fire performance increases the guarantee for the building. It is neatly cut at the edges and corners. In later construction, especially in alignment, it will be very light.

彩鋼瓦切角處理方法是什么？

What is the processing method of color steel tile corner cutting?

1.多件斜排切。

1. Multi piece diagonal cutting.

多件線按45度斜角多件排列45度角，彩鋼瓦用這種方法切角的加工效率明顯是單件切角的多倍

The multi piece line is arranged at a 45 degree angle. The processing efficiency of color steel tile chamfering by this method is obviously multiple times that of single piece chamfering

2.對稱切割兩件。

2. Cut two pieces symmetrically.

使用此方法，應提前制作一對夾角90度角的靠板。要切角的線沿著靠板兩側的端面朝向端面90度。對齊刀后，切斷夾芯板的切角部分，一次可切割兩條相互對稱切角的線。此方法僅適用于對稱切角線。如果工作臺允許，也可以同時切割4或8條線。

Using this method, a pair of backup plates with an included angle of 90 degrees should be made in advance. The line to be chamfered faces the end face 90 degrees along the end faces on both sides of the backup plate. After aligning the knives, cut off the corner cutting part of the sandwich panel, and two mutually symmetrical corner cutting lines can be cut at a time. This method is only applicable to symmetrical chamfer lines. If the workbench allows, 4 or 8 lines can be cut at the same time.

3.特殊情況下的切角。

3. Chamfer under special circumstances.

線條應切割成45度角。當彩鋼瓦的高度和底部尺寸如此之大，以至于刀片無法切割時，應改變切割角度的方式。新的角度切割方法是將線水平放置，將工作臺旋轉到一定角度，將刀片旋轉到一定角度，調整刀片與線條之間的位置關系，然后切割角度。

The lines shall be cut to a 45 degree angle. When the height and bottom size of color steel tile are so large that the blade cannot cut, the cutting angle shall be changed. The new angle cutting method is to place the line horizontally, rotate the workbench to a certain angle, rotate the blade to a certain angle, adjust the position relationship between the blade and the line, and then cut the angle.

可以看出，彩鋼瓦的切角工藝做得很好，產品在后期使用時會相對穩定。然而，如何處理切割后的棱角是我們判斷制造商產品質量的標準。因此，我們需要注意，在施工過程中也要注意施工中的裂縫，否則會影響后期使用的整體效果。還有什么不明白的地方，隨時來咨詢我們http://m.gp552.com吧！

It can be seen that the corner cutting process of color steel tile is well done, and the product will be relatively stable in later use. However, how to deal with the edges and corners after cutting is the standard for us to judge the quality of the manufacturer's products. Therefore, we need to pay attention to the cracks during construction, otherwise the overall effect of later use will be affected. If there is anything you don't understand, please feel free to consult us http://m.gp552.com Come on!